Plumbing 101: A Necessity for Installing a Bathtub
Plumbing 101: A Necessity for Installing a Bathtub
Blog Article
Just how do you actually feel about A Step-by-Step Guide to Installing a Bathtub?
Setting up a tub isn't specifically rocket science, but it does require strong plumbing, carpentry, and in some cases, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably difficult project. If the old tub is readily obtainable, the job can move immediately; if you have to open up a wall to get rid of the old bathtub and position the brand-new tub, the task is a lot harder. In either case, the task is within a residence handyman's abilities, although you will certainly need an assistant to vacate the old tub as well as embeded in the brand-new one. Ensure you have actually certified on your own for the task as well as are comfortable attempting it. Rather than employing a professional to take control of a halfway-completed project, it is far better to consider utilizing one prior to you begin. Chances are you might need an expert plumber to make tube links.
This article will assist you set up a new tub in your restroom if you have actually currently gotten a new tub and don't require to change the setup of your previous supply of water pipes.
Your tools and material checklist ought to consist of the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, then the first thing you need to do is detach the supply of water. After doing so, activate the faucets to drain any water staying in the system. The procedure of eliminating the existing taps can be quite bothersome as a result of the restricted gain access to that is often the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the remaining water that will come from the pipes. When the supply pipes have actually been eliminated, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from turning throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing compound.
Before carrying on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washers remain in location between the faucet and also the sink. Protect the tap in position with the producer provided backnut. Once the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former kind should be linked to the tap ends first, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Using both wood boards under its feet, position the bathtub in the needed setting. The wood boards are useful in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 little factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the same for the various other tap.
Activate the water as well as check all joints as well as brand-new pipework for leakages as well as tighten them if required. Fill up the bath tub as well as also check the overflow outlet and also the typical outlet for leaks.
Lastly, take care of the bath paneling as defined in the supplier's instruction manual. Tiling and also securing around the bath tub ought to wait up until the bathtub has been used at least when as this will certainly resolve it into its final setting.
Preparing for the Installation
First of all, the sustaining framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of the two faucets utilizing 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its last placement.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to split an inflexible seal, creating the water to permeate the wall surface between the bath and also the tiling, causing complications with wetness and also feasible leakages to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to enable the motion experienced when the bathtub remains in use. The sealant can split relatively early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the market. It is recommended to fit the tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that report about Installing A Bathtub through a good friend on our other website. Enjoyed our write up? Please share it. Help other people discover it. Thank-you for taking the time to read it.
Schedule Estimate Report this page